Loctite 5940 Forma guarnizioni
zoom_out_map
chevron_left chevron_right
On sale!

Loctite SI 5940 100 gr. Silicone forms Black gaskets for automotive agricultural and industrial applications

Valve cover, oil pan, engine and transmission, differential covers and gearbox.

€10.00
VAT included

Valve cover, oil pan, engine and transmission, differential covers and gearbox.

Advantages

  • Resistant to most oils and solvents
  • Excellent electrical insulation properties

Technical features

  • Description: Single-component acetic silicone
  • Elongation at break: 500%
  • Shore A hardness: 22
  • Shear strength (GBMS) in N / mm²: 1.8
  • Operating temperature: +200 ° C
  • Formats: 40ml, 100ml

TYPICAL PROPERTIES OF POLYMERIZED MATERIAL Polymerization 7 days at 23 ° C / 50% RH, on 2 mm thickness,: Physical Properties: Shore Hardness ASTM D 2240, Durometer A 22 Elongation, at break, ASTM D 412,% 500 Tensile strength , ASTM D 412 N / mm² 1.8 (psi) (260) GENERAL INFORMATION This product is not recommended for use with pure oxygen and / or oxygen rich systems and should not be used as a sealant for chlorine or other materials strongly oxidizing. For information on the safe use of this product, consult the Safety Data Sheet (MSDS). NOTES: The polymerization process can cause corrosion of some surfaces. Instructions for use 1. To obtain the best performance, the surfaces to be treated must be cleaned and degreased. 2. The polymerization by contact with the humidity starts immediately after the product is exposed to the atmosphere, therefore the pieces to be sealed must be joined within a few minutes after the product has been dispensed. 3. The adhesive must be allowed to cure (eg seven days) before subjecting it to heavy service loads. 4. The excess product can be easily removed with apolar solvents. NOTES: LOCTITE® SI 5940 ™ is not recommended for the cylinder head seal. Note The technical data contained in this document is intended as a reference. Contact the local technical service for product assistance

LOCTITE® SI 5940 ™ Cures when exposed to moisture and produces a flexible, tough oil resistant gasket. This adhesive sealant is mainly used for general use, as a filler or to form gaskets on the spot. Adheres to clean metals, glass, silicone resins, vulcanized rubbers, ceramics, natural and synthetic fibers, in addition to many plastic and painted surfaces. This adhesive is normally used in applications where the temperature range from -50 ° C to 200 ° C and can intermittently reach temperatures up to 220 ° C. TYPICAL PROPERTIES OF THE NON-POLYMERIZED PRODUCT Specific Weight @ 25 ° C 1.02 Extinction Rate, g / min 200 Flash Point - See MSDS TYPICAL PRODUCT PROPERTIES: POLYMERIZATION Skin time Skin time is the time within which the adhesive forms the superficial skin when exposed to atmospheric relative humidity between 50 ± 5% at a temperature between 25 ± 2 ° C "time-skin", minutes 14 Tack Free Time The time called Tack Free is the time required to obtain a dry, non-sticky surface. Skin time, 20 minutes

Storage Store the product in the closed container in a dry place. Storage information may also be reported on product labeling. Long-term storage Optimal storage: from 8 ° C to 21 ° C. Storage at temperatures below 8 ° C or above 28 ° C can affect the performance of the product. Materials taken from their containers may be contaminated during use. Do not return the product to the original container. Loctite assumes no responsibility for products that have been contaminated or stored in conditions other than those specified above. For more information contact the local Technical Service. Conversions (° C x 1.8) + 32 = ° F kV / mm x 25.4 = V / thousandth of an inch (mill) mm x 0.039 = inches µm x 0.039 = thousandth (mill) N x 0.225 = pounds N / mm x 5.71 = lb / in N / mm² x 145 = pounds on square inch (psi) MPa x 145 = pounds on square inch (psi) N · mx 8.851 = lb · in N · mm x 0.142 = oz · in mPa · s = cP

Loctite
2064413
New product
6.40 cm
3.20 cm
20.40 cm
0.14 kg
2020-04-21
Data sheet
Best price
Auto Additive